双轴振动筛司机操作规程
1.准备：
(1)开机前应检查三角带张紧程度和齿轮箱（油位在标准位置；
(2)检查筛板、筛邦弹簧有无断裂，铆钉螺丝是否松动；
(3)向有关岗位发出开机信号。
2.开机：
(1)筛子启动后应经常检查是否有横振现象，轴承温升是否正常（不能高于
(2)注意振动器和筛面是否有噪音，如有噪音，应检查振动器和筛板各零部件紧固情况；
(3)在振动筛正常负荷和最大负荷时应检查筛箱行程。
3.停机：
(1)除特殊事故外，禁止带料停机和停机后继续向筛子给料；
(2)按停止按钮后应检查筛子消除共振跳动的情况（方法为检查筛子扩大量，其数值不得大于工作时振幅的三倍）；
(3)筛子正常运行100-150小时后，应更换一次润滑油，以后更换周期为每月一次；
(4)检查振动器、筛箱各部螺帽是否松动，三角带张紧情况，磨损情况，当因磨损断裂而需报废时，应成套更换，以保持均匀的张力，检查减振弹簧和阻尼器情况，并将弹簧表面清理干净；
http://rywywj.lofter.com/post/1e6a80c3_c820ee8 http://rywkdks.lofter.com/post/1e698063_c7f518a http://njryw168.lofter.com/post/1e6983e5_c7ed7a8 http://rywydx.lofter.com/post/1e6a68e3_c80f58f http://rywywj.lofter.com/post/1e6a80c3_c822c1e http://njryw168.lofter.com/post/1e6983e5_c7edffb http://rywkdks.lofter.com/post/1e698063_c7f529e http://rywywj.lofter.com/post/1e6a80c3_c802928 http://njryw168.lofter.com/post/1e6983e5_c7f2f63 http://rywydx.lofter.com/post/1e6a68e3_c80c9cfhttp://ywjseo.lofter.com/post/1e634752_c64efb3 http://bjseoywj.lofter.com/post/1e66bf3e_c7105b4 http://ywjseo.lofter.com/post/1e634752_c651a95 http://ywjseo.lofter.com/post/1e634752_c64efa3 http://ywjseo.lofter.com/post/1e634752_c652ed9 http://wztgywj.lofter.com/post/1e65f473_c6f0cb8 http://bjseoywj.lofter.com/post/1e66bf3e_c7075f6 http://wztgywj.lofter.com/post/1e65f473_c6f0b71 http://bjseoywj.lofter.com/post/1e66bf3e_c7107f2 http://bjseoywj.lofter.com/post/1e66bf3e_c70fd92http://rywhw.lofter.com/post/1e5a84f4_c3db48d http://rywhw.lofter.com/post/1e5a84f4_c3db48c http://rywhw.lofter.com/post/1e5a84f4_c3db48a http://rywhw.lofter.com/post/1e5a84f4_c3db489 http://rywhw.lofter.com/post/1e5a84f4_c3db488 http://rywhw.lofter.com/post/1e5a84f4_c3db487 http://rywhw.lofter.com/post/1e5a84f4_c3db486 http://rywhw.lofter.com/post/1e5a84f4_c3db484 http://rywhw.lofter.com/post/1e5a84f4_c3db483 http://rywhw.lofter.com/post/1e5a84f4_c3db482Photo(相册)
My Groups(群组)
Good friend (好友)
